It’s a sunny day and you have been dying to go swimming. You run outside, turn on the hose, and get to work filling up your pool. How long does it take? It depends on the size of both the pool and the hose. But what if we don’t know either one? In this article, we’ll explore how to calculate how much time it will take for this task. We’ll also give you an equation that will help you find out!
Can you fill a pool with a garden hose?
The first question that needs to be addressed is whether or not a garden hose can fill a pool. There are two important factors that need to be considered in order to answer this question: the size of the pool and how long it takes for water from a garden hose to drain into an empty swimming pool.
The diameter, length, and width of pools vary greatly from model to model depending on their intended use (e.g., backyard family pools vs professional competition pools). In general, though, most residential-sized above-ground models range between 15′ x 30′ up to 20′ x 40′. The depth of these types of pools also varies based on design but usually ranges between three feet deep at its shallow end all the way down six feet deep at its deepest point.
With this in mind, it is possible to fill a pool with a garden hose if the diameter of the pool is small enough such that the water from the hose gradually fills up all sides at relatively equal rates. However, when dealing with larger pools or ones which have greater depths then using a garden hose becomes impractical and inefficient for filling them completely especially since most standard hoses are limited to about 50 gallons per minute (GPM). This means that even though you can technically use a garden hose to fill your pool slowly over time, it would take several hours before any more than an inch has accumulated on the decking around its perimeter. In fact, some smaller models might not be able fully to fill from their own weight alone depending on how fast or slow the water is being supplied from a garden hose.
On the other hand, if you have an extra-large pool and there are no obstacles in its path such as trees which could obstruct a steady flow of water then it might be possible to just use a regular old garden hose for filling purposes.
Water Pressure and How it Affects Filling Speed
One important factor of the filling process is the water pressure. Lower water pressure will result in a long time to fill but may be more suitable for some people depending on their situation.
In order to accurately calculate how long it takes to fill your pool with a garden hose, you must determine what type of faucet provides access to that source of water.
If you live in a single-family home, there is probably only one faucet that provides access to the waterline. This also usually means that your hose can reach all areas of your yard and if not then it will at least be relatively close by (provided that you do not have an above-ground pool).
However, if you are like most people living in apartments or condos, they may only provide access to either a showerhead inside your residence or possibly community amenities such as an outside watering station for plants. These types of sources would take much longer than filling directly from household plumbing because they lack pressure; therefore it is important to specify this type of information when asking someone how long does it take to fill with a garden hose.
How to Determine the Water Pressure of Your Hose
There are a few simple steps that can be taken in order to determine the water pressure of your hose.
The first step is to attach the garden hose nozzle and turn on the faucet, but do not open it completely because this will force too much water through at one time which may cause damage to both your plumbing and home (not recommended).
Afterward, adjust the flow control valve until you reach an optimal speed for filling; then measure how long it takes to fill up a bathtub or other container with known measurements like gallons or liters. If necessary make adjustments by either opening up more on the valve if your container fills too quickly or lessening it if needed so that it has just enough strength in which you feel comfortable using.
In most cases when using just the nozzle on your watering device, PSI is around 40-60 which will determine its ability to move larger volumes of water at once.
This number varies depending on several factors given previously mentioned such as household plumbing and overall length of hose; however, for home use filling small pools or containers should not take more than an hour even if there are low pressures involved.
Filling Speeds of Different Common Sized Pools
Now let’s assume that you are filling pools of different sizes. For reference, the average American swimming pool is between 16-20 feet long but can be as small as 52 inches in diameter (yes, I know what you’re thinking…). When it comes to figuring out how fast your water pressure will fill a pool, consider this simple equation:
The larger the hose and nozzle size = The faster the rate of flow.
So now let’s say we want to figure out how long it would take for us to fill our 20 foot by 40-foot in-ground vinyl lined pool if we were using an unregulated garden hose with no sprayer attached at 25 psi? Here goes nothing!
We need to first convert the length into feet. We have twenty feet in our pool, so we will multiply 20 by 12 to get the total length of 240 feet. We are going to assume that there are no obstacles or restrictions where you want your hose placed (like a yard), but if there is something obstructing it, make sure to take this into consideration! It’s time for another simple equation:
Length of hose, divided by the flow rate (in gallons per minute) = Number of minutes required to fill.
Now that we’ve determined our length is 240 feet and our water pressure at 28 psi, let’s divide the number like so: 240/28= approximately eight minutes it would take for us to completely fill up this pool with a garden hose! Not too shabby right? But what if I told you there was an even faster way?!
Since most people are limited on time or patience when filling their pools via standard hoses connected to your hose spigot, one option might be investing in something called a booster pump. A booster pump will help increase your overall water pressure coming into your home which can consequently speed up the process of filling your pool significantly.
How Much Does It Cost to Fill a Pool with Water?
The next worrying question is how much does it cost to fill a pool with water?
You may be surprised to find that even filling your own pool is not cheap. You can expect the price of filling up a small backyard swimming pool (or spa) will set you back about $100 – and this doesn’t include any additional costs such as electricity or labor fees if you’re paying someone to fill it for you.
If the pool is large or public, then this price can jump up dramatically.
The average price of filling up an above-ground swimming pool is about $60 for every thousand gallons needed. This can fluctuate based on where you live and other circumstances such as the distance required to transport the water or whether there are any additional fees associated with pumping out your septic system before filling the pool.
It’s best to get multiple quotes before committing if this will be something done by yourself without professional assistance because prices range widely throughout different areas in America. If having your local company fill your pool sounds appealing then expect to pay around one hundred dollars or more per hour that they work plus whatever fuel charge they charge.
How to Fill a Pool Without a Hose
There are a few ways to get around using your garden hose to fill the pool.
- Use a bucket
You can use a large plastic container or two five-gallon buckets and have someone hold them as you pour water into it from above. You will either need to go up on the ladder or raise one of those containers with some sort of rope/pulley system.
- Fill with a fire hose
If you have access to one of these, they are very strong and can accommodate large amounts of water quickly. Using this method won’t cost any money (if it’s your fire department) but will probably take some time if there is no one else around to help out. You could also call the local pool store or newspaper and ask them for someone who would be willing to donate their time/services in exchange for advertising & mention on social media etc…
- Use a submersible pump
This option costs the most initially ($100+) however it doesn’t require anyone to hold anything as well as stores inside so that it is ready when next year! The only downside is that it doesn’t work too well with very large pools.
- Use a pool cover pump
This option also costs money ($100+) and is only really worth the investment if you have a larger than average size pool to fill (15,000 gallons or more). This method will require someone else to hold something as well but works without electricity so no need for extension cords either! The advantage of this system is that because your not filling from above like in other methods there’s little chance for debris such as leaves falling into your new clean water. It does however require extra storage space both inside & out.
- Well Water
This method is free, however, it will require effort on your part to make sure the water quality is acceptable (chlorine levels, etc). The downside of this option is that if you do not already have well water & live in an area where there are wells available for public use, chances are they aren’t too close.
- Rainwater
Another way to avoid using tap water for filling would be rain barrels. These can be bought relatively cheaply and work very similar to a submersible pump except with no electricity required! You could either hook up multiple rain barrels or buy one large enough to accommodate all the pool’s volume without having someone hold anything while you fill it which makes things much easier/quicker overall.
Check more guides about garden hoses:
- How to Remove Corrosion From a Garden Hose?
- How to Heat Water From Garden Hose?
- How to Remove Garden Hose Connector?
FAQ
How long does it take to fill a 5000-gallon pool with a garden hose?
It takes about 45 minutes to fill a 5000-gallon pool with a garden hose. This calculation is based on using 30 psi of water pressure, filling the pool at 11 gallons per minute (GPM), and having an average flow rate of .0029 cubic meters per second.
Will 2 hoses fill a pool faster than 1?
Yes. If you have two hoses hooked up to the spigot, it will fill your pool faster than if only one hose is running into the pool. When using two hoses, each hose should be receiving around 11 GPM (gallons per minute).
Can I fill my pool overnight?
Yes, you can fill your pool overnight. However, if the ambient temperature is above 85 degrees F, then it’s recommended that you drain and refill your pool every 12 hours to avoid algae growth in the pool.
How long does it take to fill a 10000 gallon pool with a garden hose?
The time it takes to fill a 10000 gallon pool using a garden hose will depend on the size and type of hose. Generally, it will take at least 8 hours to fill a 10000 gallon pool with a standard 5/8 inch garden hose. If you have a larger hose or one with a higher flow rate, your pool will fill up faster. If you’re filling the pool from an outside faucet, you also need to make sure that your water pressure is high enough for the job. It is also important to note that if your garden hose has an inadequate flow rate, it could take considerably longer than 8 hours to fill your pool.
By renting or purchasing a hose with a larger diameter, you can significantly reduce the time it takes to fill your pool. These hoses can increase the flow rate of your water and reduce the time it takes to fill your pool. If you want to further increase the pressure and speed of your water supply, consider investing in a booster pump.
If you’re still having trouble filling your pool with a garden hose, it could be beneficial to contact a professional plumber for advice. After assessing the size and type of your garden hose, they will advise you on the best way to fill your pool quickly.
How many minutes does it take to fill a 24-foot swimming pool with water from a garden hose?
Depending on the rate of your garden hose and the size of your pool, this will affect how long it takes to fill up. On average, it takes about 3-4 hours to fill a 24 foot round pool with a garden hose.
Depending on the rate of water flow from your garden hose, you can fill up your pool in record time or at a leisurely pace. A higher-flow garden hose will pump more gallons of water per minute than a lower-flow model.
Moreover, the force of water coming out of your garden hose impacts performance. A higher pressure allows for more gallons per minute but also has greater potential to damage or erode any plastic parts that are connected to the end of the hose.
How long does it take to fill a 15000 gallon pool with a garden hose?
The amount of time it takes to fill a pool with a hose depends on the size of the hose and water pressure from your home’s plumbing system. It would typically take one person around 20 to 30 hours to fill a 15000 gallon pool by using a garden hose. If you have a 3/4 inch diameter garden hose, it can deliver about 23 gallons of water per minute. That means it would take nearly 650 minutes, or slightly more than 10 hours and 50 minutes, to fill the entire pool. However, factors such as less water pressure or smaller hoses may increase the amount of time required for filling the pool. If you are filling an above-ground pool that is shorter than 48” in depth and has a capacity of 15000 gallons or less, then one hour should be enough time to refill the pool.
When filling a large volume of water, it’s recommended to use a pool fill hose that has a diameter of 1-1/4 inch or greater. This larger size will ensure more consistent water pressure and enable you to fill your 15000 gallon pool in less time than with smaller hoses.
Additionally, if you have access to a sprinkler system connected to your home’s plumbing lines, then this may be an even faster way to refill the pool.
How long does it take to fill a 13000 gallon pool with a garden hose?
First, the size of the hose is important. A larger hose will fill a pool much quicker than a smaller one. If you have access to a large diameter garden hose that can deliver up to 10 gallons of water per minute, then it should take around 13 hours to fill a 13000 gallon pool. However, if you only have access to a standard 3/4 inch garden hose that delivers around 2 gallons per minute, it could take 65 hours or more for the same pool!
The flow rate of your water source also affects how long it takes to fill a pool. If the water is flowing at extremely high pressure from an irrigation well or other large source, then the pool will fill much faster than if the water is coming from a lower pressure hose spigot.
Finally, the size of the pool’s opening also matters. If you have an above-ground pool with a small skimmer or narrow opening, then it may take longer for the water to fill up compared to an in-ground pool with a large opening.
It’s important to factor all of these variables into consideration when determining how long it will take to fill your pool. With the right setup and equipment, filling a 13000 gallon pool with a garden hose could be as quick as 13 hours – but it could also take many more hours depending on the circumstances. In any case, patience is key!
How much water does it take to fill a pool with a garden hose?
The amount of money you spend to fill up your pool with water from a hose is determined by how much your local government charges for water usage. Generally speaking, it costs around $0.003-$0.015 per gallon to fill up a pool with tap water. So if you were to fill a 13000 gallon pool, it would cost between $39 and $195 depending on the water rates in your area.
If you are looking for ways to save money on filling up your pool, consider collecting rainwater or using gray water from other sources such as showers and washing machines. These methods will help reduce the amount of money spent on filling up your pool.
How soon after filling a pool сan you swim?
If you want to swim in your newly filled pool as soon as possible, there are certain steps that need to be taken after the pool has been filled. First, it’s important to check and make sure that all of the necessary chemical levels are balanced. This includes testing the pH, alkalinity, chlorine and stabilizer levels in order to create a safe swimming environment.
Once the chemical balance has been established, it is important to shock the pool with chlorine or another sanitizer. This will help kill any bacteria and algae in the water. After shocking, wait 24-48 hours before entering the water to allow for proper circulation and filtration of chemicals throughout the pool.
Is it cheaper to fill the pool with a garden hose?
Yes, it is much cheaper to fill a pool with a garden hose than it is to hire professionals or purchase large amounts of water. Depending on your local water rate, filling up a 13000 gallon pool can cost anywhere from $39-$195 when using a garden hose. This is significantly less expensive than other methods such as hiring someone to truck in water or having the pool filled professionally.
In addition to cost savings, filling a pool with a garden hose also gives you more control over the process and allows you to monitor how quickly the pool is filling up. It’s important to note that certain factors such as hose size, flow rate of the water source, and size of the opening will affect how long it takes to fill the pool. However, with a little planning and patience, filling a pool with a garden hose is one of the most cost-effective ways to get your pool ready for swimming season!
What is the first thing you do after you fill a pool with water?
The first thing you should do after filling a pool with water is to test and balance the chemical levels in the water. This includes testing for pH, alkalinity, chlorine and stabilizer levels in order to create a safe swimming environment. If these levels are off, it can cause skin irritations and other health issues for swimmers.
Once the chemical levels have been balanced, you need to shock the pool with chlorine or another sanitizer. This will help kill any bacteria and algae in the water. After shocking, wait 24-48 hours before entering the water to allow for proper circulation and filtration of chemicals throughout the pool. After this important step is complete, you can finally enjoy your freshly filled pool!
How do I fill my pool for the first time?
Filling your pool for the first time can seem like a daunting task, but with some planning and patience you will soon be able to enjoy it.
The first step is to determine how much water you need in order to fill up your swimming pool. If you are using a garden hose, keep in mind that certain factors such as hose size, flow rate of the water source, and size of the opening will affect how long it takes to fill the pool. Calculate this ahead of time so that you know approximately how long it should take.
Once you are ready to begin, connect the garden hose to a source of water with adequate pressure and turn it on. Place the end of the hose into your pool and let the water slowly fill up until it reaches the desired level. This process can take anywhere from several hours to several days depending on how much water your pool requires and how large your hose is.
Be sure to monitor the flow rate closely as it can be easy to accidentally overfill a pool if left unattended for too long. Do not forget to check that all valves are in proper working condition before turning on any taps or hoses, as this could create a dangerous situation. If possible, try using an automatic shut-off valve so that you do not have to monitor the flow rate as closely.
What is the best way to fill in an inground pool?
The best way to fill in an inground pool is to use a dedicated pump and filter system. This approach will ensure that the water entering your pool is clean, free of debris, and safe for swimming. Connecting a garden hose to the pump can help speed up the process but make sure that you monitor the flow rate closely so as not to overfill or flood your pool area. Properly maintaining your pump and filter system is essential for keeping your pool’s water clean and clear.
Filling your inground pool with a garden hose alone can be time consuming and difficult to manage, especially if the source of water has a low pressure output. The slower the flow rate of your water source, the longer it will take to fill your pool. Therefore, it is important to consider the size of your pool and determine whether or not a garden hose is suitable for the task at hand.
Overall, there are several steps to consider when filling your inground pool for the first time. Calculate how much water you will need, inspect the condition of all valves before turning on any taps or hoses, monitor the flow rate closely, and invest in a pump and filter system if necessary. Following these steps can help ensure that your swimming experience is safe and enjoyable.
Useful Video: How Long Does It Take To Fill A Swimming Pool?
Final Thoughts
Now that you know how long it takes to fill a pool with different scenarios, it’s time for you to weigh out all of your options and decide what is best for your specific needs!
Remember though; if you are living in an area where there isn’t much water pressure at the source (which can be common), or this just happens to be something on your bucket list so-to-speak, investing in one might not hurt either. Since they don’t require any additional electrical work but simply hook up between two hoses that come directly from the well/pump system located underneath ground level.
We hope that this article has given you a little more insight into how long it takes to fill a pool with different setups, and now you are able to make an educated decision on whether or not buying one of these would be beneficial for your family.
Remember that if you have any questions about filling up your own swimming pool, feel free to contact us! And as always…happy filling!